日韩a级一片-日韩a免费-日韩a视频-日韩va-大香交伊人-大香焦久久

外觀Appearance

外觀不應有顯著的污點、裂紋。

There shall not be any remarkable stain，rust or crack on the appearances.

標示應該很容易辨識。

Marking shall be easily legible.

機械特性Mechanical characteristics

拉力強度試驗Tensile test

將保險絲固定好后，對保險絲引線施加5N的拉力，持續1分鐘。試驗過后，保險絲沒有任何破損現象。

Exert the axial pulling force of 5N to the both ends of lead wire for 1 minute. After the test the fuse shall be no damage and loosening.

 電氣特性Electrical characteristics

實驗條件Test condition

所有測試環境溫度為25±5℃。

All electrical characteristics tests are conducted at an ambient temperature of 25±5℃.

分?jǐn)嗄芰?/font>Interrupting rating test

保險絲能承受的分?jǐn)嗄芰?/font>：35A或10倍的額定電流當中較大的。分?jǐn)嗄芰y(cè)試后測得保險

絲的絕緣阻抗值大于0.1ΜΩ。

The fuse interrupting capacity：35A or 10 times the rated current whichever is greater. After

interrupting, the insulation resistance between the fuse terminations shall be not less than 0.1ΜΩ.

3溫度上升試驗：通1.5倍額定電流15分鐘，然后每隔15分鐘增加0.1倍額定電流。測得保

險絲斷開時任何部位的溫升不得超過135℃，周?chē)h(huán)境溫度為25±5℃。

Temperature Rising Test: The rated current of 1.5 times is applied for 15 minutes. After the first 

15minutes, the current is increased by 0.1 times the rated current every 15 minutes until the fuse

operates. The temperature rising on the fuse surface is not higher than 135℃.

 時間-電流特性 Time-Current Characteristics

 耐久性測試 Endurance test

對保險絲通過相關標準規格單規定的額定電流1小時,然后截?cái)嚯娏?/font>15分鐘,將該循環重復

100次。試驗過后保險絲沒有任何破損現象。

   A ampere rating specified in the relevant standard sheet is passed through the fuse for a period of

1h.The current is then switched off for a period of 15 minutes. This cycle is repeated 100 times. After

the test the fuse shall be no damage and loosening.

 焊接參數 Soldering parameters

 波峰焊 260℃,最大10秒，

Wave soldering 260 ℃,10 sec. Maximum  

 手工焊 370℃,最大5秒，

Manual soldering 370℃, 3 sec. Maximum

時間電流曲線圖見附頁 Time- current curve see attachment

環境特性Environmental characteristics

使用溫度范圍 Operating Temperature

-55℃～125℃。

保存條件Storage Conditions

相對濕度≦75%，可存放3年。

Relative humidity ≦ 75%, store 3 years .